LiSa SWIR 2K Linescan InGaAs Camera

LiSa SWIR 2K Linescan InGaAs Camera

Sensor Type

InGaAs

Resolution

2048 x 1

Pixel pitch

7.5 µm square or 7.5 x 220 µm

Shutter Mode - Frame rate full frame

Global - 60k lines/sec

Readout noise

N/A

Interface

CameraLink

LiSa SWIR 2K Linescan InGaAs Camera

The LiSa SWIR 2K-M-SE linescan InGaAs camera integrates the T-Cooled sensor NSC1801T-SI Monochrome. This camera integrates control of temperature to improve the intrinsic characteristics of the sensor. The camera is composed of Sensor, ADC, FPGA and Interface boards:

  • Sensor board integrates the sensor and the Peltier (thermoelectric cooler).
  • ADC board
  • FPGA board delivering the entire control signal sensor and the camera processing
  •  Interface board integrates the management of the main power supply, the trigger, the Peltier management and the Gigabit transceiver.

The LiSa SWIR 2K-M-SE linescan InGaAs camera provides output data video through mini Camlink connector (SDR26)

The LiSa SWIR 2K-M-SE linescan InGaAs camera uses single stage TE cooler to control the temperature. Please note that the NUC and BPR files are delivered only for +25°C. The Camera has 3 TEC modes

  • Low current < 1 W
  • Medium current < 2 W
  • Large current < 4 W

TEC temperature setting

The cooling temperature capacity greatly depends on the heat dissipation. By default, with the additional heat dissipaters, the achievable TEC setting is 5 to 10° below ambient temperature depending on convection possibilities. By default, the NUCs are calibrated in factory at 25°C.
Heat dissipaters can be mounted on the side of the camera for increased performance (increased temperature delta by 10 to 15°C). For more detailed information, contact us at info@axiomoptics.com

Features control

  • You can choose manually the gain and offset you want to apply on the image. There is no automatic gain/offset control
  • Correction 1-Point or 2-Point calibrated in factory (User can carry out own NUC)
  • NUC mode can be Automatic/Manual In manual you can load any NUC calibration file from the flash. In automatic the camera interpolates the NUC depending on exposure time.
  • Correction of bad pixel calibrated in factory (possible to realize it also by user)
  • Temperature sensor reading. Resolution: 0.1462°C/LSB

 

Description

LiSa SWIR 2K Linescan InGaAs Camera

The LiSa SWIR 2K-M-SE linescan InGaAs camera integrates the T-Cooled sensor NSC1801T-SI Monochrome. This camera integrates control of temperature to improve the intrinsic characteristics of the sensor. The camera is composed of Sensor, ADC, FPGA and Interface boards:

  • Sensor board integrates the sensor and the Peltier (thermoelectric cooler).
  • ADC board
  • FPGA board delivering the entire control signal sensor and the camera processing
  •  Interface board integrates the management of the main power supply, the trigger, the Peltier management and the Gigabit transceiver.

The LiSa SWIR 2K-M-SE linescan InGaAs camera provides output data video through mini Camlink connector (SDR26)

The LiSa SWIR 2K-M-SE linescan InGaAs camera uses single stage TE cooler to control the temperature. Please note that the NUC and BPR files are delivered only for +25°C. The Camera has 3 TEC modes

  • Low current < 1 W
  • Medium current < 2 W
  • Large current < 4 W

TEC temperature setting

The cooling temperature capacity greatly depends on the heat dissipation. By default, with the additional heat dissipaters, the achievable TEC setting is 5 to 10° below ambient temperature depending on convection possibilities. By default, the NUCs are calibrated in factory at 25°C.
Heat dissipaters can be mounted on the side of the camera for increased performance (increased temperature delta by 10 to 15°C). For more detailed information, contact us at info@axiomoptics.com

Features control

  • You can choose manually the gain and offset you want to apply on the image. There is no automatic gain/offset control
  • Correction 1-Point or 2-Point calibrated in factory (User can carry out own NUC)
  • NUC mode can be Automatic/Manual In manual you can load any NUC calibration file from the flash. In automatic the camera interpolates the NUC depending on exposure time.
  • Correction of bad pixel calibrated in factory (possible to realize it also by user)
  • Temperature sensor reading. Resolution: 0.1462°C/LSB